SC16C2550

Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder

SC16C2550

Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder

SC16C2550BIB48

5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs; 2 channel UART\n5 V, 3.3 V and 2.5 V operation\n5 V tolerant on input only pins\nIndustrial temperature range\nPin and functionally compatible to 16C2450 and software compatible with INS8250, SC16C550\nUp to 5 Mbit/s data rate at 5 V and 3.3 V and 3 Mbit/s at 2.5 V\n16-byte transmit FIFO to reduce the bandwidth requirement of the external CPU\n16-byte receive FIFO with error flags to reduce the bandwidth requirement of the external CPU\nIndependent transmit and receive UART control\nFour selectable Receive FIFO interrupt trigger levels\nSoftware selectable baud rate generator\nStandard asynchronous error and framing bits (Start, Stop and Parity Overrun Break)\nTransmit, Receive, Line Status and Data Set interrupts independently controlled\nFully programmable character formatting: 5-bit, 6-bit, 7-bit or 8-bit characters\nEven, odd or no-parity formats\n1, 1 1/2 or 2-stop bit\nBaud generation (DC to 5 Mbit/s)\nFalse start-bit detection\nComplete status reporting capabilities\n3-state output TTL drive capabilities for bidirectional data bus and control bus\nLine break generation and detection\nInternal diagnostic capabilities: Loopback controls for communications link fault isolation\nPrioritized interrupt system controls\nModem control functions (CTS, RTS, DSR, DTR, RI, DCD)\n;

The SC16C2550B is a two channel Universal Asynchronous Receiver and Transmitter (UART) used for serial data communications. Its principal function is to convert parallel data into serial data and vice versa. The UART can handle serial data rates up to 5 Mbit/s.\nThe SC16C2550B is pin compatible with the ST16C2550. It will power-up to be functionally equivalent to the 16C2450. The SC16C2550B provides enhanced UART functions with 16-byte FIFOs, modem control interface, DMA mode data transfer. The DMA mode data transfer is controlled by the FIFO trigger levels and the RXRDYn and TXRDYn signals. On-board status registers provide the user with error indications and operational status. System interrupts and modem control features may be tailored by software to meet specific user requirements. An internal loopback capability allows on-board diagnostics. Independent programmable baud rate generators are provided to select transmit and receive baud rates.\nThe SC16C2550B operates at 5 V, 3.3 V and 2.5 V and the industrial temperature range, and is available in plastic PLCC44, LQFP48, DIP40 and HVQFN32 packages.\n

SC16C2550BIBS

5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs; 2 channel UART\n5 V, 3.3 V and 2.5 V operation\n5 V tolerant on input only pins\nIndustrial temperature range\nPin and functionally compatible to 16C2450 and software compatible with INS8250, SC16C550\nUp to 5 Mbit/s data rate at 5 V and 3.3 V and 3 Mbit/s at 2.5 V\n16-byte transmit FIFO to reduce the bandwidth requirement of the external CPU\n16-byte receive FIFO with error flags to reduce the bandwidth requirement of the external CPU\nIndependent transmit and receive UART control\nFour selectable Receive FIFO interrupt trigger levels\nSoftware selectable baud rate generator\nStandard asynchronous error and framing bits (Start, Stop and Parity Overrun Break)\nTransmit, Receive, Line Status and Data Set interrupts independently controlled\nFully programmable character formatting: 5-bit, 6-bit, 7-bit or 8-bit characters\nEven, odd or no-parity formats\n1, 1 1/2 or 2-stop bit\nBaud generation (DC to 5 Mbit/s)\nFalse start-bit detection\nComplete status reporting capabilities\n3-state output TTL drive capabilities for bidirectional data bus and control bus\nLine break generation and detection\nInternal diagnostic capabilities: Loopback controls for communications link fault isolation\nPrioritized interrupt system controls\nModem control functions (CTS, RTS, DSR, DTR, RI, DCD)\n;

The SC16C2550B is a two channel Universal Asynchronous Receiver and Transmitter (UART) used for serial data communications. Its principal function is to convert parallel data into serial data and vice versa. The UART can handle serial data rates up to 5 Mbit/s.\nThe SC16C2550B is pin compatible with the ST16C2550. It will power-up to be functionally equivalent to the 16C2450. The SC16C2550B provides enhanced UART functions with 16-byte FIFOs, modem control interface, DMA mode data transfer. The DMA mode data transfer is controlled by the FIFO trigger levels and the RXRDYn and TXRDYn signals. On-board status registers provide the user with error indications and operational status. System interrupts and modem control features may be tailored by software to meet specific user requirements. An internal loopback capability allows on-board diagnostics. Independent programmable baud rate generators are provided to select transmit and receive baud rates.\nThe SC16C2550B operates at 5 V, 3.3 V and 2.5 V and the industrial temperature range, and is available in plastic PLCC44, LQFP48, DIP40 and HVQFN32 packages.\n

SC16C2550B

5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs

SC16C2550B

5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs

SC16C2550B_07

5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs

SC16C2550BIA44

5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs

SC16C2550BIA44

5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs

SC16C2550BIB48

5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs