S9S08MP16E2MLF中文資料恩XP數(shù)據(jù)手冊PDF規(guī)格書

Features

? 8-Bit HCS08 Central Processor Unit (CPU)

– Up to 51.34 MHz CPU at 2.7V to 5.5V across temperature

range of –40°C to 105°C

– Up to 40 MHz CPU at 2.7V to 5.5V across temperature range

of –40°C to 125°C

– HC08 instruction set with added BGND instruction and

additional addressing modes for LDHX and STHX

– Support for up to 48 interrupt/reset sources

? On-Chip Memory

– Up to 16 KB flash memory; read/program/erase over full

operating voltage and temperature

– Up to 1 KB random-access memory (RAM)

– Security circuitry to prevent unauthorized access to RAM and

flash memory contents

? Power-Saving Modes

– Two low power stop modes; reduced power wait mode

– Peripheral clock gating can disable clocks to unused modules

? Clock Source Options

– Oscillator (XOSC) — Loop-control Pierce oscillator; Crystal

or ceramic resonator range of 31.25–38.4 kHz or 1–16 MHz

– Internal Clock Source (ICS) — Containing a

frequency-locked-loop (FLL) controlled by internal or

external reference; precision trimming of internal reference

allows 0.2 resolutions and 2 deviation over temperature

and voltage; supports CPU frequencies up to 51.34 MHz

? System Protection

– Watchdog computer operating properly (COP) reset running

from dedicated 1-kHz internal clock source or bus clock

– Low-voltage detection with reset or interrupt; selectable trip

points

– Illegal opcode and illegal address detection with reset

– Flash memory block protection

? Development Support

– Single-wire background debug interface

– Breakpoint capability to allow single breakpoint setting during

in-circuit debugging (plus three more breakpoints in on-chip

debug module)

– On-chip in-circuit emulator (ICE) debug module containing

three comparators and nine trigger modes. Eight deep FIFO for

storing change-of-flow addresses and event-only data. Debug

module supports both tag and force breakpoints

? Peripherals

– IPC — Interrupt Priority Controller with 4 programmable

interrupt priority levels

– ADC — 13-channel, 12-bit resolution; 2.5 ?s conversion time;

automatic compare function; 1.7 mV/?C temperature sensor;

internal bandgap reference channel; operation in stop3

– PGA — Differential programmable gain amplifier with

programmable gain (x1, x2, x4, x8, x16, or x32)

– HSCMP — Three fast analog comparators with positive and

negative inputs; separately selectable interrupt on rising and

falling comparator output; filtering; windowing; HSCMP1 and

HSCMP2 outputs can be optionally routed to FTM1 module;

runs in stop3

– DAC — Three 5-bit digital to analog convertor used as a

32-tap voltage reference for each comparator

– PDB — Two programmable delay blocks: PDB1 synchronizes

PWM with samples of ADC; PDB2 synchronizes PWM with

comparing window of analog comparators

– SCI — Full duplex non-return to zero (NRZ); LIN master

extended break generation; LIN slave extended break

detection; wake up on active edge

– SPI — Full-duplex or single-wire bidirectional;

Double-buffered transmit and receive; Master or Slave mode;

MSB-first or LSB-first shifting

– IIC/SMBus — Up to 400 kbps; Multi-master operation;

Programmable slave address; Interrupt driven byte-by-byte

data transfer; supports broadcast mode and 10-bit addressing;

SMBus compatible

– FTM — Two Flextimers with total of 8 channels; One

2-channel (FTM1) and one 6-channel (FTM2); supports

operation up to 2x bus clock; selectable input capture, output

compare, edge- or center-aligned PWM; dead time insertion;

fault inputs

– MTIM — 8-bit modulo counter with 8-bit prescaler

– RTC — (Real-time counter) 8-bit modulus counter with

binary or decimal based prescaler; External clock source for

precise time base, time-of-day, calendar or task scheduling;

Free running on-chip low power oscillator (1 kHz) for cyclic

wake-up without external components, runs in all MCU modes

– CRC — Cyclic redundancy check generator

– KBI — Three 8 channel keyboard interrupt module with

software selectable polarity on edge or edge/level modes

Input/Output

– 40 GPIOs, 2 output-only pins.

– Hysteresis and configurable pull up device on input pins;

Configurable slew rate and drive strength on output pins;

Sink/Source current up to 20mA

Package Options

– 48-LQFP, 32-LQFP, 28-SOIC

– 48-LQFP qualified for automotive usage