PCA9541AD

2-to-1 I2C-bus master selector with interrupt logic and reset; 2-to-1 bidirectional master selector\nI2C-bus interface logic; compatible with SMBus standards\nPCA9541A/01 powers up with Channel 0 selected\nPCA9541A/03 powers up with no channel selected and either master can take control of the bus\nActive LOW interrupt input\n2 active LOW interrupt outputs\nActive LOW reset input\n4 address pins allowing up to 16 devices on the I2C-bus\nChannel selection via I2C-bus\nBus initialization/recovery function\nBus traffic sensor\nLow Ron switches\nAllows voltage level translation between 1.8 V, 2.5 V, 3.3 V and 5 V buses\nNo glitch on power-up\nSupports hot insertion\nSoftware identical for both masters\nLow standby current\nOperating power supply voltage range of 2.3 V to 5.5 V\n6.0 V tolerant inputs\n0 Hz to 400 kHz clock frequency\nESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM perJESD22-C101\nLatch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA\nPackages offered: SO16, TSSOP16, HVQFN16\n;

The PCA9541A is a 2-to-1 I2C-bus master selector designed for high reliability dualmaster I2C-bus applications where system operation is required, even when one masterfails or the controller card is removed for maintenance. The two masters (for example,primary and back-up) are located on separate I2C-buses that connect to the samedownstream I2C-bus slave devices. I2C-bus commands are sent by either I2C-bus masterand are used to select one master at a time. Either master at any time can gain control ofthe slave devices if the other master is disabled or removed from the system. The failedmaster is isolated from the system and will not affect communication between the on-linemaster and the slave devices on the downstream I2C-bus.\nTwo versions are offered for different architectures. PCA9541A/01 with channel 0selected at start-up, and PCA9541A/03 with no channel selected after start-up.\nThe interrupt outputs are used to provide an indication of which master has control of thebus. One interrupt input (INT_IN) collects downstream information and propagates it tothe 2 upstream I2C-buses (INT0 and INT1) if enabled. INT0 and INT1 are also used to letthe previous bus master know that it is not in control of the bus anymore and to indicatethe completion of the bus recovery/initialization sequence. Those interrupts can bedisabled and will not generate an interrupt if the masking option is set.\nA bus recovery/initialization if enabled sends nine clock pulses, a not acknowledge, and aSTOP condition in order to set the downstream I2C-bus devices to an initialized statebefore actually switching the channel to the selected master.\nAn interrupt is sent to the upstream channel when the recovery/initialization procedure iscompleted.\nAn internal bus sensor senses the downstream I2C-bus traffic and generates an interruptif a channel switch occurs during a non-idle bus condition. This function is enabled whenthe PCA9541A recovery/initialization is not used. The interrupt signal informs the masterthat an external I2C-bus recovery/initialization must be performed. It can be disabledand an interrupt will not be generated.\nThe pass gates of the switches are constructed such that the VDD pin can be used to limitthe maximum high voltage, which will be passed by the PCA9541A. This allows the use ofdifferent bus voltages on each pair, so that 1.8 V, 2.5 V, or 3.3 V devices can communicatewith 5 V devices without any additional protection.\nThe PCA9541A does not isolate the capacitive loading on either side of the device, so thedesigner must take into account all trace and device capacitances on both sides of thedevice, and pull-up resistors must be used on all channels.\nExternal pull-up resistors pull the bus to the desired voltage level for each channel. All I/Opins are 6.0 V tolerant.\nAn active LOW reset input allows the PCA9541A to be initialized. Pulling the RESET pinLOW resets the I2C-bus state machine and configures the device to its default state asdoes the internal Power-On Reset (POR) function.\n

恩XP

PCA9541AD/01

2-to-1 I2C-bus master selector with interrupt logic and reset

Generaldescription ThePCA9541Aisa2-to-1I2C-busmasterselectordesignedforhighreliabilitydualmasterI2C-busapplicationswheresystemoperationisrequired,evenwhenonemasterfailsorthecontrollercardisremovedformaintenance.Thetwomasters(forexample,primaryandback-up)

ETC

PCA9541AD/01

絲印：PCA9541AD/1；Package：SO16；2-to-1 I2C-bus master selector with interrupt logic and reset

Generaldescription ThePCA9541Aisa2-to-1I2C-busmasterselectordesignedforhighreliabilitydual masterI2C-busapplicationswheresystemoperationisrequired,evenwhenonemaster failsorthecontrollercardisremovedformaintenance.Thetwomasters(forexample, primaryandback-u

ETC

PCA9541AD/03

2-to-1 I2C-bus master selector with interrupt logic and reset

Generaldescription ThePCA9541Aisa2-to-1I2C-busmasterselectordesignedforhighreliabilitydualmasterI2C-busapplicationswheresystemoperationisrequired,evenwhenonemasterfailsorthecontrollercardisremovedformaintenance.Thetwomasters(forexample,primaryandback-up)

ETC

PCA9541AD/03

絲?。?a target="_blank" title="Marking" href="/pca9541ad/3/marking.html">PCA9541AD/3；Package：SO16；2-to-1 I2C-bus master selector with interrupt logic and reset

Generaldescription ThePCA9541Aisa2-to-1I2C-busmasterselectordesignedforhighreliabilitydual masterI2C-busapplicationswheresystemoperationisrequired,evenwhenonemaster failsorthecontrollercardisremovedformaintenance.Thetwomasters(forexample, primaryandback-u

ETC

PCA9541ADSLASH01

絲?。?a target="_blank" title="Marking" href="/pca9541ad/1/marking.html">PCA9541AD/1；Package：SO16；2-to-1 I2C-bus master selector with interrupt logic and reset

Generaldescription ThePCA9541Aisa2-to-1I2C-busmasterselectordesignedforhighreliabilitydual masterI2C-busapplicationswheresystemoperationisrequired,evenwhenonemaster failsorthecontrollercardisremovedformaintenance.Thetwomasters(forexample, primaryandback-u

ETC

PCA9541ADSLASH01

2-to-1 I2C-bus master selector with interrupt logic and reset

Generaldescription ThePCA9541Aisa2-to-1I2C-busmasterselectordesignedforhighreliabilitydualmasterI2C-busapplicationswheresystemoperationisrequired,evenwhenonemasterfailsorthecontrollercardisremovedformaintenance.Thetwomasters(forexample,primaryandback-up)

ETC

PCA9541ADSLASH03

絲?。?a target="_blank" title="Marking" href="/pca9541ad/3/marking.html">PCA9541AD/3；Package：SO16；2-to-1 I2C-bus master selector with interrupt logic and reset

Generaldescription ThePCA9541Aisa2-to-1I2C-busmasterselectordesignedforhighreliabilitydual masterI2C-busapplicationswheresystemoperationisrequired,evenwhenonemaster failsorthecontrollercardisremovedformaintenance.Thetwomasters(forexample, primaryandback-u

ETC

PCA9541ADSLASH03

2-to-1 I2C-bus master selector with interrupt logic and reset

Generaldescription ThePCA9541Aisa2-to-1I2C-busmasterselectordesignedforhighreliabilitydualmasterI2C-busapplicationswheresystemoperationisrequired,evenwhenonemasterfailsorthecontrollercardisremovedformaintenance.Thetwomasters(forexample,primaryandback-up)

ETC