NE1617A

Temperature monitor for microprocessor systems

DESCRIPTION TheNE1617Aisanaccuratetwo-channeltemperaturemonitor.Itmeasuresthetemperatureofitselfandthetemperatureofaremotesensor.Theremotesensorisadiodeconnectedtransistor.ThiscanbeintheformofeitheradiscreteNPN/PNP,suchasthe2N3904/2N3906,oradiodeconn

PHI

NE1617A

Temperature monitor for microprocessor systems

Generaldescription TheNE1617Aisanaccuratetwo-channeltemperaturemonitor.Itmeasuresthetemperatureofitselfandthetemperatureofaremotesensor.Theremotesensorisadiodeconnectedtransistor.ThiscanbeintheformofeitheradiscreteNPN/PNP,suchasthe2N3904/2N3906,oradi

ETC

NE1617A

Smart, simple solutions for the 12 most common design concerns

ETC

NE1617ADS

Temperature monitor for microprocessor systems

DESCRIPTION TheNE1617Aisanaccuratetwo-channeltemperaturemonitor.Itmeasuresthetemperatureofitselfandthetemperatureofaremotesensor.Theremotesensorisadiodeconnectedtransistor.ThiscanbeintheformofeitheradiscreteNPN/PNP,suchasthe2N3904/2N3906,oradiodeconn

PHI

NE1617ADS

Temperature monitor for microprocessor systems

Generaldescription TheNE1617Aisanaccuratetwo-channeltemperaturemonitor.Itmeasuresthetemperatureofitselfandthetemperatureofaremotesensor.Theremotesensorisadiodeconnectedtransistor.ThiscanbeintheformofeitheradiscreteNPN/PNP,suchasthe2N3904/2N3906,oradi

ETC

NE1617ADS

Temperature monitor for microprocessor systems;

General description\nThe NE1617A is an accurate two-channel temperature monitor. It measures the temperature of itself and the temperature of a remote sensor. The remote sensor is a diode connected transistor. This can be in the form of either a discrete NPN/PNP, such as the 2N3904/2N3906, or a diode connected PNP built into another die, such as is done on some Intel microprocessors.\nThe temperature of both the remote and local sensors is stored in a register that can be read via a 2-wire SMBus. The temperatures are updated at a rate that is programmable via the SMBus (the average supply current is dependent upon the update rate — the faster the rate, the higher the current).\nIn addition to the normal operation, which is to update the temperature at the programmed rate, there is a one-shot mode that will force a temperature update.\nThere is also an alarm that senses either an overtemperature or undertemperature condition. The trip points for this alarm are also programmable.\nThe device can have one of nine addresses (determined by two address pins), so there can be up to nine of the NE1617A on the SMBus.\nIt can also be put in standby mode (in order to save power). This can be done either with software (over the SMBus) or with hardware (using the STBY pin).\nFeatures and benefits\n■ Replacement for Maxim MAX1617 and Analog Devices ADM1021\n■ Monitors local and remote temperature\n■ Local (on-chip) sensor accuracy:\n? ? ±2 °C at 60 °C to 100 °C\n? ? ±3 °C at -40 °C to 125 °C\n■ Remote sensor accuracy:\n? ? ±3 °C at 60 °C to 100 °C\n? ? ±5 °C at -40 °C to 125 °C\n■ No calibration required\n■ Programmable overtemperature/undertemperature alarm\n■ SMBus 2-wire serial interface up to 100 kHz\n■ 3 V to 5.5 V supply range; 5.5 V tolerant\n■ 70 μA supply current in operating mode\n■ 3 μA (typical) supply current in standby mode\n■ ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101\n■ Latch-up testing is done to JEDEC standard JESD78, which exceeds 100 mA\n■ Small 16-lead SSOP (QSOP) package\n

恩XP