MP401

40 Amp Single Phase Bridge Rectifier 50 to 1000 Volts

Features ●MountingHoleFor#8Screw ●PlasticCaseWithMetalBottom ●AnyMountingPosition ●SurgeRatingOf400Amps

MP401

40 Amp Single Phase Bridge Rectifier 50 to 1000 Volts

MP401

整流橋;

MP4010

40 Amp Single Phase Bridge Rectifier 50 to 1000 Volts

Features ●MountingHoleFor#8Screw ●PlasticCaseWithMetalBottom ●AnyMountingPosition ●SurgeRatingOf400Amps

MP4010S

40,50S IN-LINE BRIDGE RECTIFIER

FEATURES ?DiffusedJunction ?LowForwardVoltageDrop ?HighReliability ?HighSurgeCurrentCapability ?IdealforPrintedCircuitBoards ?DesignedforSavingMountingSpace ?ULRecognizedFile#E157705

MP4010S

BRIDGE RECTIFIERS 35 to 50 Amps

MP4010W

40 Amp Single Phase Bridge Rectifier 50 to 1000 Volts

Features ●MountingHoleFor#8Screw ●PlasticCasewithMetalBottom ●AnyMountingPosition ●SurgeRatingOf400Amps

MP4012

8V-55Vin Boost WLED Controller; ● Constant-current WLED Driver \n● 8V-55V Input Voltage \n● Constant Frequency Mode Or Constant Off Time Mode \n● Programmable Switching Frequency or Off-Time \n● Leading Edge Blanking for Current Sense \n● High Frequency PWM Dimming and Analog Dimming \n● Output-to-Input Disconnect in Shutdown Mode \n● Synchronization Function \n● Programmable Over Voltage Protection \n● Open Load Hiccup Mode Protection \n● Short Load Hiccup Mode Protection \n● Programmable Current Limit \n● UVLO, Thermal Shutdown \n● Soft Start \n● Available in 16-pin SOIC package\n;

The MP4012 is a current mode controller designed for driving the high brightness Light Emitting Diodes (LEDs) from extremely wide input voltage 8V-55V. It can be used in Boost, Buck, Buck-boost and SEPIC topologies.?The MP4012 drives external MOSFET with fixed frequency/constant off-time architecture to regulate the LED current, which is measured through an external current sense resistor. Its feedback voltage can be adjusted by the external DC bias voltage. The MP4012 can work in constant frequency operation mode or constant off time mode. It features programmable slop compensation that can optimize the control loop regulation and avoid sub harmonic oscillation.?The MP4012 implements high frequency PWM Dimming with external disconnect MOSFET. It achieves analog dimming by adjusting the feedback voltage. The MP4012 has synchronizing function, which makes multiple ICs synchronized to each other by connecting SYNC pins together.?The MP4012 includes under-voltage lockout, over voltage protection, open and short hiccup mode protection, overload protection and thermal protection to prevent damage in the case of fault condition.?The MP4012 is available in a 16-pin SOIC package.

MP4013

High Power Switching Applications. Hammer Drive, Pulse Motor Drive and Inductive Load Switching

HighPowerSwitchingApplications HammerDrive,PulseMotorDriveandInductiveLoadSwitching ?Smallpackagebyfullmolding(SIP10pins) ?Highcollectorpowerdissipation(4-deviceoperation) :PT=4W(Ta=25°C) ?Highcollectorcurrent:IC(DC)=2A(max) ?HighDC

MP4015

TOSHIBA Power Transistor Module

HighPowerSwitchingApplications HammerDrive,PulseMotorDrive InductiveLoadSwitching ?Smallpackagebyfullmolding(SIP10pins) ?Highcollectorpowerdissipation(4-deviceoperation):PT=4W(Ta=25°C) ?Highcollectorcurrent:IC(DC)=5A(max) ?HighDCcurrentgain:hFE=