ISL81486

5V, Half Duplex, 30Mbps, RS-485/RS-422 Transceiver; ? Specified for 10% Tolerance Supplies\n? High Data Rates ISL4486 up to 40Mbps ISL81486 up to 30Mbps\n? Large Differential Output Voltage 3V into 54?\n? Low Bit-to-Bit (Part-to-Part) Skew for Parallel Applications\n? 0.6 Unit Load Allows up to 50 Devices on the Bus\n? ISL81486 is a Drop-In Replacement for the ADM1486\n? Low Quiescent Current 800μA\n? -7V to +12V Common Mode Input Voltage Range\n? Three State Rx and Tx Outputs\n? 14ns (Max) Propagation Delays, 2ns (Max) Skew\n? Operates from a Single +5V Supply (10% Tolerance)\n? Current Limiting and Thermal Shutdown for driver Overload Protection;

Support is limited to customers who have already adopted these products.\n\nThe Intersil ISL4486 and ISL81486 are BiCMOS, 5V powered, single transceivers that meet both the RS-485 and RS-422 standards for balanced communication, and feature the larger output voltage and higher data rate - up to 40Mbps - required by high speed PROFIBUS applications. Unlike competitive products, these Intersil devices are specified for 10% tolerance supplies (4. 5V to 5. 5V) and deliver at least a 2. 3V differential output voltage over this supply range. At the 5% tolerance specified by many competitors, the ISL4486 delivers an unsurpassed 2. 5V differential signal into a 54? total load. This translates into longer reach, or better data integrity, at the exceptional 40Mbps data rate. SCSI applications benefit from the ISL4486's low receiver and transmitter part-to-part skews, which make it perfect for high speed parallel applications where large numbers of bits must be simultaneously captured. The low bit-to-bit skew eases the timing constraints on the data latching signal. These devices present a 0. 6 unit load to the RS-485 bus, which allows up to 50 transceivers on the network. Receiver (Rx) inputs feature a fail-safe if open design, which ensures a logic high Rx output if Rx inputs are floating. Driver (Tx) outputs are short circuit protected, even for voltages exceeding the power supply voltage. Additionally, on-chip thermal shutdown circuitry disables the Tx outputs to prevent damage if power dissipation becomes excessive.

ISL81486

5V, Ultra High Speed, PROFIBUS, RS-485/RS-422 Transceivers

ISL81486IB

5V, Ultra High Speed, PROFIBUS?, RS-485/RS-422 Transceivers

Features ?Specifiedfor10ToleranceSupplies ?HighDataRates ISL4486..........................upto40Mbps ISL81486.........................upto30Mbps ?LargeDifferentialOutputVoltage..........3Vinto54? ?LowBit-to-B

ISL81486IBZ

5V, Ultra High Speed, PROFIBUS?, RS-485/RS-422 Transceivers

Features ?Specifiedfor10ToleranceSupplies ?HighDataRates ISL4486..........................upto40Mbps ISL81486.........................upto30Mbps ?LargeDifferentialOutputVoltage..........3Vinto54? ?LowBit-to-B

ISL81486IU

5V, Ultra High Speed, PROFIBUS?, RS-485/RS-422 Transceivers

Features ?Specifiedfor10ToleranceSupplies ?HighDataRates ISL4486..........................upto40Mbps ISL81486.........................upto30Mbps ?LargeDifferentialOutputVoltage..........3Vinto54? ?LowBit-to-B

ISL81486IUZ

5V, Ultra High Speed, PROFIBUS?, RS-485/RS-422 Transceivers

Features ?Specifiedfor10ToleranceSupplies ?HighDataRates ISL4486..........................upto40Mbps ISL81486.........................upto30Mbps ?LargeDifferentialOutputVoltage..........3Vinto54? ?LowBit-to-B

ISL81486IB

5V, Ultra High Speed, PROFIBUS, RS-485/RS-422 Transceivers

ISL81486IB-T

5V, Ultra High Speed, PROFIBUS, RS-485/RS-422 Transceivers

ISL81486IBZ

5V, Ultra High Speed, PROFIBUS, RS-485/RS-422 Transceivers

ISL81486IBZ-T

5V, Ultra High Speed, PROFIBUS, RS-485/RS-422 Transceivers